GTAP2250D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Belinda from FLORENCE, KY
- Parts Used:
- WH41X10096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LEXINGTON, OH
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Kiln, MS
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from State College, PA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Port Hueneme, CA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MARSHALLTOWN, IA
- Parts Used:
- WH12X10614C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Machine would lose power and shut itself off.
Unplugged machine. Used tape markers to identify knobs then removed control knobs with vigorous straight pull. Unscrewed three screws on rear of control panel face and tilted control panel over with a small sideways slide, to expose circuit board. Laid new circuit board alongside old and transferred jumper block and wiring terminals from old board to same positions on new. Unscrewed old board and removed. Put in new board and tightened screws. Replaced back panel and knobs. Plugged in machine and tested. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from BERKLEY, MA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Plastic pipe developed a tear and leaked drain water.
Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sallie from WEAVERVILLE, NC
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All of the fins on the bottom had broken due to clothes getting caught in them.
Removed the softener despenser by pulling it straight up, then did the same with the agitator, except I had to turn it a little then pull straight up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oraila from RINCON, GA
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken part
We pulled out the old parts and then we got the new parts and we put them in,
Was this instruction helpful to you?
Thank you for voting!