Models > GTAP2250D1WW > Instructions

GTAP2250D1WW General Electric Washer - Instructions

Jump to:

All Instructions for the GTAP2250D1WW
106 - 120 of 245
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dave from Irving, TX
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Washing machine flooding
The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Campbell, CA
Parts Used:
WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
Two out of Four Straps were Torn
First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Washougal, WA
Parts Used:
WH41X22935
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
hose had a crack in the crease causeing leak .
I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Helmut J from New Berlin, WI
Parts Used:
WH12X10276
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from OVERLAND PARK, KS
Parts Used:
WH12X10334
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from LEXINGTON, OH
Parts Used:
WH23X10043
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from BEACHWOOD, OH
Parts Used:
WH41X365
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Washing machine never stops filling and thus overflows
Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.

Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.

Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from ELMIRA, NY
Parts Used:
WH41X365
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from MARSHALLTOWN, IA
Parts Used:
WH12X10614C
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Machine would lose power and shut itself off.
Unplugged machine. Used tape markers to identify knobs then removed control knobs with vigorous straight pull. Unscrewed three screws on rear of control panel face and tilted control panel over with a small sideways slide, to expose circuit board. Laid new circuit board alongside old and transferred jumper block and wiring terminals from old board to same positions on new. Unscrewed old board and removed. Put in new board and tightened screws. Replaced back panel and knobs. Plugged in machine and tested. Done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jose from Rosemead, CA
Parts Used:
WH23X10043
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifton from WAUKEGAN, IL
Parts Used:
WH41X22935
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from CONYERS, GA
Parts Used:
WH01X10302
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pansy from STARKVILLE, MS
Parts Used:
WH12X10334
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Washer wouldn't spin out
Someone did it for me.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arlis from Moore, SC
Parts Used:
WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joel from mt vernon, IL
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTAP2250D1WW
106 - 120 of 245