EWA2500A0WW General Electric Washer - Instructions

I reached under the agitator on two sides with my fingers and with one good upward yank the agitator came loose. I removed the agitator from the inside of the machine, I seen the Agitator Coupling was spinning in both directions so I felt that it may have been broken. I removed the one bolt hold the Agitator Coupling in place, I remove and inspected the Coupling and noticed that the spline was worn out. I cleaned the transmission spine that the Coupling slides over with a wire brush while using a shop vacuum to catch any loose debris. I installed new Agitator Coupling Kit slipped the Agitator back inside the machine over the coupling and pressed it down until it snapped into place. Job done. Machine works great.

I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.

Worked Perfectly

Once I found your web page things went very smoothly and quickly. It was exactly what I wanted and it even came a day early. Obviously, no problem with the repair just put the knob in place.

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

popped the front off and unscrewed the top to get to the water inlet. With plyers twisted the wire tie that holds the hose in place and unscrewed the tiny screws off to get the inlet off. then replace it with my new Hose & Water Inlet.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

It was really simple just pull up the agitator and take off the screw that holds the coupling down slide it off and put the new coupling on and you are done.

An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone

Yes, we should have done this a long time ago and put off replacing the starter knob and heat adjuster knob. By the time they no longer worked, we called in an expensive repairman. When we realized what the problem was, we thanked him, paid him lots of money and did what we should have all along - replaced the knobs throug partsselect.com instead of using the repairman for another $150.00.

We received the knobs within 3 days (paying for medium fast delivery was worth it) and simply pulled the old problem knobs off and put the other ones on. Simple, no brainer work.

Save yourself expensive repairs and replace those knobs when they start going. Also, when you test the machine, make sure you turn the setting to a time (stupid mistake that most of us do) to make sure that the knobs work properly.

Good luck. A terrific experience with Partselect.com. Would use again in the future and recommend to others.