WISQ416CT7WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- SAM from ROCK HILL, NY
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken START knob on dryer.
Slid off the old START knob, then pushed on the new START knob.
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Irvine, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The inside of the Selector Knob was stripped
Removed the damaged knob and replaced it with the new knob. Very ease
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from West End, NC
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob cracked
ordered part on line--received in mail 2 days later--
just pushed on in 2 seconds--job done
how much easier can it get??????
just pushed on in 2 seconds--job done
how much easier can it get??????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Woodbridge, VA
- Parts Used:
- WH12X1043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid switch failed
First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Burley, ID
- Parts Used:
- WH12X10069
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pressure switch would not detect water level.
I replaced the pressure switch which I ordered from A-1. It still did not work. I then took a small rigid wire and inserted it into the pressure box on the side of the tub. Then I squirted water thru the tube to clean out the hole where the tube from the pressure switch is hooked up. The washer then worked fine. The pressure switch I replaced was probably OK. This was a learning experiance which cost me $68.00. Still cheaper than a repairman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Marion, MA
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Loud bang during spinning
Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lapeer, MI
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Betterton, MD
- Parts Used:
- WH45X10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The machine would not spin and the agitator seemed to be siezed up. The inner tub had cracked and broken completely loose causing it to jam against itself preventing any movement.
1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Clermont, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke off
I ordered a selector knob and it was delivered in a short amount of time. I wasn't sure if it was the right one when I ordered it, but my husband just put it right on the dryer. He said it was perfect. Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Boone, NC
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Start knob was broken
Ordered new knob from you people and simply replaced borken knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Miami, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Pulled the old knod off and put the new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rahway, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janis from northridge, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Easy. Pulled off old one slipped on new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!