WCXR1070A1AA General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Prestonsburg, KY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator would'nt move
pulled agitator off unscrewed bolt holding coupling on put new coupling on bolt in place put agitator on. washer working good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- crystal from lexington, NC
- Parts Used:
- WH12X10065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water Level Pressure Switch Was Bad
Remove back of washer, remove switch, replace with new pressure switch attach elements and put back of washer back on --fixed washer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from channelview, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Well Is The Second Time That Happen
First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from Key West, FL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
would not agitate
Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from Lyndhurst, NJ
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Agitator broke
Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jorge from Pinehurst, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the agitator is not moving. (agitating).
take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from reidsville, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
no agitation on washer
it wasn't as hard as i thought it would be. just remove the
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corrine from Minot, ND
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
would not agitate
took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from st james, NY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
washer was not agitating or spinning
The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Grants Pass, OR
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Machine did not agitate.
Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ostrander, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator was not working
Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Philadelphia, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
the agitator on my washer was'nt turning
This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Brandon, FL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer wouldn't agitate, but everything else worked.
This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONALD from DURANT, OK
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
would not Agitate
Unplugged washing machine pulled Agitator strait up removed screw from center of Agitator coupling . Replaced coupling put Agitator back on plugged in and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Onel from Blandon, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
washer would not wash
first i removed the spindle and theni removed theplastic coupling
Was this instruction helpful to you?
Thank you for voting!