WCSE3100A2WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- daniel from walkersville, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
tub wouldn't drain
Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from mazeppa, MN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken dampening straps
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from woodland, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cumberland, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from BRADFORD, RI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not pump out
Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Wrightwood, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
wouldn't pump water
I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ignacio from Portage, IN
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would not pump water out into drain
First I removed the Front panel with a screwdriver, poped right out. Disconnected the two wires, removed two clamps from hoses on pump, then two screws at base. removed old pump, installed new pump ,tighten two screws, reinstalled hoses and clamps to pump, then put front panel back on, job completed in less than 1/2 hour. tested washer, pump worked and drained tub. easy fix saved cost to repairman $150 plus part cost.
Thanks for the information , learned how to change pump from another repair story on your web site!!
Thanks for the information , learned how to change pump from another repair story on your web site!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Woodruff, UT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench set
Pump was noisy, then failed and hummed.
The pump arrived and because I'd read some of the other stories here I wasn't too upset that it looked different.
I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.
The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.
I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.
The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Nampa, ID
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Wouldn't pump water
Removed the old pump put in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mansfield, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water pump died
Was easy. Removed pump, ordered yours and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Rochester, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water on final pump out
Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!