WPSR4130W1AA General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- FERNANDO from ALAMOGORDO, NM
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The agitator would spin freely by hand.
I first placed a rope under the fins of the agitator and used a 2X4 board to pull up the agitator which needed very little force to release itself from the agitator coupling. I removed the nut holding the agitator coupling, removed the stripped agitator coupling. Installation was just the reverse process, inserted the new agitator coupling, placed and tightened the screw, and pressed down the agitator over the agitator coupling and I was done. Over time for the repair was between 5 and 10 minutes, very easy, and I have no experience repairing washing machines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mansfield, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water pump died
Was easy. Removed pump, ordered yours and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SHIRLEY, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water would not pump out of the unit or spin
If you follow the video that part select provides you will be just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from BRADFORD, RI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not pump out
Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Spotsylvania, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
would not drain
watched Partselect video and followed instructions step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ridgeland, MS
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water wasn't being pumped out.
The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST CHESTER, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Stopped agitating
I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L. from Mandeville, LA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water pump failed
Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not rotate
1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Beaumont, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would finish a cycle and the water would not drain the tub.
I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Singers Glen, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump was broken
So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Riverbank, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was no longer moving
I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Wytheville, VA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Agitator Not Working
I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Waynesburg, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer would not agitate
We removed the agitator then the bolt holding couplier. The inside of the plastic couplier had stripped after 5 years. We cleaned around the metal part of the agitator then installed the new GE plastic couplier, put in the bolt & replaced the agitator. The machine works better than ever.
The GE website said this part had to be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
The GE website said this part had to be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!