WISR409DGBWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from woodland, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from mazeppa, MN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken dampening straps
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cumberland, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from bradford, VT
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from BRIMFIELD, MA
- Parts Used:
- WH43X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Not agitating, free spinning agitator
Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CONYERS, GA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burley from WINTER PARK, FL
- Parts Used:
- WH41X10077
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fill nozzle had a leak
Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wagdy from Watertown, MA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The two dial buttons were broken on a white appliance. The dials sent were bone white.
Pull out old, insert new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Dunmore, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer wouldnt start
just replaced the old knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob
the part fixed all the problems in a cinch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fort Worth, TX
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Machine wouldn't fill, losing water out back
Determined the drain hose on the back of the machine was leaking, due to my dog chewing on the hose. Replaced the hose with the new one, locked the dog out of the garage where the machine is located, problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy from sulligent, AL
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
busted drain hose
It was really easy to replace i removed the old one & sliped on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Sebring, FL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer would not spin
removed old dampening straps replaced with new ones a total of 4 straps, took about 10 min, works great again.very easy to do. thank you.
Was this instruction helpful to you?
Thank you for voting!