WJSR1070A2AA General Electric Washer - Instructions

As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.

First I removed the Front panel with a screwdriver, poped right out. Disconnected the two wires, removed two clamps from hoses on pump, then two screws at base. removed old pump, installed new pump ,tighten two screws, reinstalled hoses and clamps to pump, then put front panel back on, job completed in less than 1/2 hour. tested washer, pump worked and drained tub. easy fix saved cost to repairman $150 plus part cost.
Thanks for the information , learned how to change pump from another repair story on your web site!!

This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.

removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.

removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

After doing some research on the problem I decided that the rubber tub dampers were probably the problem. Replacing them was simple and straight forward after watching the video. A test spin after installation revealed that the problem still existed. This time I watched the bottom of the tub with a flashlight as the spin cycle began and I discovered that the concrete counter-weight was loose on its platform. General Electric had attached a 5 lb concrete block to the tub support with two self tapping sheet metal screws that had stripped out. I screwed the screws back in and added two nuts to the protruding screw bottom and locked them together. Problem solved. The main difficulty in this repair is reaching to the back of the washing while laying on the floor. And sharp edges on everything.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

This site and buying experience WOWED ME!!! After realizing what happened, I searched how to open up a washer, since I had never done it before. My search brought me to your site, which had an excellent 'how to' video for my exact problem of replacing the pump! I ordered the part, which was delivered to my door in LESS than 24 hours! Unfortunately, there was undrained water in the washing machine so while undoing the clamps on the old pump, the water drained on my kitchen floor, so beware of that issue. Because of the positioning of the pump, the clamps were a little tricky to redo, but completed without too much difficulty. I also had to 'unplug' (with a coat hanger snake)the drain tube connecting the pump to the back of the washing machine so it could flow to the outside drain pipe. This was the best internet buying experience I have ever had! Thank you so much! I fixed a 15 year old washing machine for about $40.00!!! (And I am a 57 year old grandmother ;-) Woohoo!!!

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

replaces as per video. Very helpful