WJSR1070A2AA General Electric Washer - Instructions

figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.

First removed tub comming from Tub and removed srcew to replace. Has to twist part out of slot to remove installed in reversed order. Really easy to do.

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

Removed the knob from water level switch. Removed 4 screws holding the control panel cover on and leaned it out. Made sure the washer was unplugged and removed the three wires and removed the water level hose and the switch. Installed the new switch and hose plugged the wires back in and put things back together. Washer works fine now.

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

Watch the videos you might be a little skeptical at first. I watched the videos about 8-10 times before I bought the part so I took my part out first then got back on you tube watched a few more videos and got on parts select website found the part matched it up to what I pulled out of my washer ordered it got to me in a weeks time put it in and working like new again cost about 14.00 shipping and part together saved about 200.00 per my estimate I had to fix it.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.