WJSR2080TAWW General Electric Washer - Instructions

An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!

Took the top cup off the agitator, popped out the agitator by grabbing it with both hands and yanking, unscrewed the nut to the agitator coupling, put the new one on and tightened it up, popped the agitator back on. Works great no problems. Though I did find out that the factory had changed the part sometime ago and it actually did need to be replaced.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.

Simple replacement. Very easy.