S5100D1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WH02X10383, WH2X1198, WH2X1197
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin, leaking water
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from Berkeley, CA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from crescent, FL
- Parts Used:
- WH12X10271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not spin out the wash
the repair whent very easy like you said thankyou
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Davie, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Debris in pump
Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ranburne, AL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator coupling in my washer was stripped out.
I had already removed the old coupling by removing pulling the agitator straight up off the coupling, then I removed the bolt that held the coupling in, and pulled the coupling up off the shaft.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tammy from tracy, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the agitator was not sping
figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beulah from MISSOURI CITY, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
CLOTHERS NOT AGITATING
REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from LIBERTY, KS
- Parts Used:
- WH02X10383, WH2X1197
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Very loud noise during spin cycle
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RUMFORD, RI
- Parts Used:
- WH01X10088
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replaced start button
My rubber start button gave out after 10+ years...kept getting stuck inward and was unreliable. I thought about buying a new washer but my old one still works fine and the new ones are super expensive! My wife and I only do a couple of loads per week so decided to try to fix it ourselves.
Ordered a new one from this site. Was about $20.00 for the new button, but I have not spent a dime in over 10 years! I just cannot believe how easy it is to find the part and place an order. All you really need to do is to find the tag on the washer with the model number. What a fantastic business and website!
The install was easy...pulled out the old one using a pair of needle nose pliers (still useable in an emergency) and installed the new one. I was smart enough to coat the new one with a little Vaseline and it slipped (wiggled) right into place. For the record, the washer works just fine without the button too.
Glad I tried to fix it. Would have cost me a couple hundred bucks for a professional repair.
Good work ! PERFECT!
Ordered a new one from this site. Was about $20.00 for the new button, but I have not spent a dime in over 10 years! I just cannot believe how easy it is to find the part and place an order. All you really need to do is to find the tag on the washer with the model number. What a fantastic business and website!
The install was easy...pulled out the old one using a pair of needle nose pliers (still useable in an emergency) and installed the new one. I was smart enough to coat the new one with a little Vaseline and it slipped (wiggled) right into place. For the record, the washer works just fine without the button too.
Glad I tried to fix it. Would have cost me a couple hundred bucks for a professional repair.
Good work ! PERFECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from GRENADA, MS
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
noise tub moving too much
pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from DOVER, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Tub shacking
Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Syracuse, IN
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Would not agitate
Reading all the other stories helped me get started. One tip I want to share is when removing the old coupler, I held on to a pulley puller by hand. I hooked the jaws underneath; while I pulled up on it, I would tap with a hammer on either side of the old coupler. This gave me the leverage needed to make it pop right off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!