WNSB9100B0CC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Syracuse, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer wasnt draining properly, yet you could hear the pump turning.
Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from bradford, VT
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cumberland, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burley from WINTER PARK, FL
- Parts Used:
- WH41X10077
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fill nozzle had a leak
Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from RIDGE, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Washer was stalling in rinse cycle and not draining
Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from mazeppa, MN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken dampening straps
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Silver Spring, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not empyting
Removed front cover, disconnected wires and hoses, reversed process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Edina, MO
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
washing machine quit agitating
took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from woodland, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
Was this instruction helpful to you?
Thank you for voting!