WHDRR418E6WW General Electric Washer - Instructions

Part Select inclusion of parts diagram helped determine which part was broken, and how to disassemble just what was necessary. I was planning to open up the control panel to get inside, which was not necessary. Assembly was simple for the same reason. Sometimes, it does help to read the "manual" first....

I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)

I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.

I replaced the pressure switch which I ordered from A-1. It still did not work. I then took a small rigid wire and inserted it into the pressure box on the side of the tub. Then I squirted water thru the tube to clean out the hole where the tube from the pressure switch is hooked up. The washer then worked fine. The pressure switch I replaced was probably OK. This was a learning experiance which cost me $68.00. Still cheaper than a repairman

Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.

1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

took two people to get this belt on

replaced Tub dampeners Straps.

Replaced lid switch with wire harness. Video available on this web page. The technician said bad motor. We counted the flashes, light on top of motor, was 7 times. Diagnoses are very important, save you money! Do it more times, be sure. Biggest problem is socket size for the screws, size 6,5mm or 1/4 inch. Do not call technician or throw away your washer!...

After confirming what I thought was the problem and reading other posts it was fairly easy to replace the belt. After taking the bottom cover loose to gain access to the large and small pulley I found out that the belt was very tight to get on as a previous customer had mentioned. I also used visegrips to hold the belt in place on the large pulley while guideing the belt on the small motor pulley with one hand and turning the drum pulley with the other hand. It helped that I had read the other post first. Next time will be a snap.

Uhhhhhh.... Pulled knob off. Pushed new knob on. Took all of 5 seconds.

Removed bottom washer plate. Placed belt on small, grooved pulley. Started belt on larger pulley. Clamped lock pliers to larger pulley to prevent belt from slipping off. Turned belt onto larger pulley by turning and pressing the belt close to the smaller pulley. Adjusted belt and replaced bottom plate.

When disassembling I could not remove the 1 3/4" tub nut with in house tools and had to order the spanner wrench. Almost mandatory unless you have a socket wrench.

Removed front panel, cut two wires to switch ( color coded ) snapped old switch out and installed new switch, connected wires with wire nuts. Removed two screws in lid, removed magnet and installed the new one. A caveman could do it!

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!