GTWP2000F0WW General Electric Washer - Instructions

Easy to replace, take off the front cover take off hoses unscrew and attach the new pump. Problem wasn't the pump. Now that I have a new pump, not sure what to do next.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

The washer came apart fairly easy until I tried removing tub nut Huge Problem!! After beating the spanner wrench to death I purchased a $50 43mm impact socket to remove the nut. I cleaned up the tub and shaft and started reassembly by replacing bearing 6006rs that I found locally. When I started installing the tub seal I ran into a major issue. Seal would not fit properly, it was to loose in tub. The seal was not large enough for outside diameter. It was a 1/16 of inch or so off. I tried two seals and neither one would work. After talking with a retired repair tech I found that the tub was bad and that the old seal had corroded so bad that it expanded the tub seal housing. I decided not to spend anymore money for this junk of a washer and I applied rtv sealant & reassembled. I'll use it until it breaks down and trash it, very bad design for tub seal, nothing holds it in place, pushed up out of tub. I don't think the rtv sealant well hold for very long. I do appreciate the instructional video for repairs, they are very helpful for showing procedures as to the repair but it's a new machine that's used and everything comes apart so easy. 5 year old washer doesn't come apart that easy. It took 2 weeks to fix it after waiting on parts and doing a unconventional repair to tub seal. So now my wife has started searching for another washer because this one is running on a prayer!

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

plugged on the wires and hase than snaped in place. the delay of the part was the hard part.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.