GTWP1000M2WW General Electric Washer - Instructions

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Just slipped it on. No problems, No Tools.

Remove control knob and replace it with new part.

One retaining clip to remove and replace part.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Turned off the both the hot and cold water. Removed the hoses from the back of the control panel. Removed 3 panel screws to expose the inside of the component parts. Removed the 2 screws holding the valve. Installed the new valve. Then I pulled off the knob for the temperature control. To remove the switch, you need to press the tab that locks in the switch and turn the switch counter clockwise to remove the switch from the panel. Reverse the operation to reinstall the new switch. Pay close attention to the 4 wires that clip to the switch to get them in proper order. Reinstall the control panel and and reattach the hoses.

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

I followed partselect repair videos to see how to pop off the front panel and also remove the top control panel. Lay the control panel on top of the washer and leave everything connected. With power disconnected I first checked the fill tube and fill sensor by pulling the rubber tube off the bottom of the drum and blowing in the tube - you can hear the sensor click on and off. It requires more pressure if you set the water level switch to a larger load. This behavior told me the tube and sensor were working but this must be an airtight system to be reliable. To test for slow air leaks I blew in the tube to cause the switch to click, then clamped the rubber tube shut with a C-clamp. I left it overnight and no leaks - the switch was still activated in the morning, as I could hear it click when I released the C-clamp. I then suspected the fill valve, so I plugged in the power cord, set the washer for a load and started it. The water started filling and I unplugged the power cord, which should cause the fill valve to shut off immediately. It did not - it kept on filling with water, but in this case eventually shut off after 60-90 seconds. Since it did not shut off immediately when power was removed I knew the fill valve was sticking. I ordered the fill valve from partselect and received it in a couple days. Replacement was easy - shut off water, remove the hoses, and then 3 screws and two electrical connectors to swap out the valve. Then 3 screws to put the control panel back on and snap the front panel back in place. Done. Since replacing the fill valve the washer has been working perfectly.

You tube is the only way to go!

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.