Models > GTWN5550D1WW > Instructions

GTWN5550D1WW General Electric Washer - Instructions

Jump to:

All Instructions for the GTWN5550D1WW
106 - 120 of 188
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
robert from bradford, VT
Parts Used:
WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Cumberland, MD
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from STANFIELD, NC
Parts Used:
WH23X10043
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Socket set
Replacing drain pump
The job was rather simple. After removing front panel with the aid of a putty knife to push back the spring clamps under the top panel, the pump is in plain view. Remove the two mounting screws and push back the spring clamps that secure the connection hoses. Squeezing the spring clamps that hold the hoses onto the pump can be a bit troublesome so I removed the spring clamps completely and replaced them with radiator hose clamps which made the job a whole lot easier. Replaced the front panel and the job was finished.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from LEXINGTON, OH
Parts Used:
WH23X10043
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ashley from DAYTONA BEACH, FL
Parts Used:
WH12X10479
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Knob had broken off from pressure switch
Very simple took control board off and unplugged hose and wire twisted it out and just put new part in
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jose from Rosemead, CA
Parts Used:
WH23X10043
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arnold from OSWEGO, IL
Parts Used:
WH12X10479
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The plastic tab that the dial knob slides on broke off the switch.
The pressure switch came out easily however I had to get the control panel to lay flat to slide the new switch in place. I finally determined that you have to slide the panel to the left to get it out of the slots and thus lay it flat on the washer lid. Wish the washer instructions told you that. Part fit perfectly and is easier to change the water level than the original part. I think the original part was rubbing and that finally broke the tab.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from BEACHWOOD, OH
Parts Used:
WH41X365
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Washing machine never stops filling and thus overflows
Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.

Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.

Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from CONYERS, GA
Parts Used:
WH01X10302
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifton from WAUKEGAN, IL
Parts Used:
WH41X22935
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set, Wrench (Adjustable)
Would not drain and hose had a hole
Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from ELMIRA, NY
Parts Used:
WH41X365
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pansy from STARKVILLE, MS
Parts Used:
WH12X10334
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Washer wouldn't spin out
Someone did it for me.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter from woodland, CA
Parts Used:
WH01X39337
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
B. from WILLISTON, FL
Parts Used:
WH02X10383, WH02X10265
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
water was dripping down onto the belt and stopping movement
front back and top have to come off, but contrary to 'youtube' instructions, 'nothing' has to be disconnected, if the washer is pulled away from the wall and power unplugged things can be unscrewed and pushed back enough to pull the inner tub out and get to the seal without disconnecting water lines wires or anything else.. the main shaft nut is aluminum and the shaft is 'castellated' so alittle penetrating oil on it and a short 10" pipe wrench in conjunction with a 2lb sledge busted it loose easy enough so i didnt need to buy a spanner .. the seal was easy to get out with a couple of screwdrivers wedged in the sides .. the old split ring crumbled upon removal also so get one of those .. i lucked out on the washer that goes with it and mine was still usable but if it was rusted any more than it was i wouldve needed that also .. so good idea to get the 3 items if your doing the seal - seal, split ring, and washer - another thing, i cleaned everything up good, knocked everything off with a brass brush, polished the shaft seal area with some 600 grit and then lubed the seal with silicone grease thinking it might be hard to get in .. it wasnt .. and it leaked slightly until i did several loads .. in hindsight it would be better to 'lightly' coat the outer edge of the seal that mates to the tub with a good silicone gasket maker, the inner lips with the grease would be fine ... so thats about how it went, parts came quick and i had it all fixed up in a couple of hours .. cleaning things as i went probably took longer than the wrenching ..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James C from HINESVILLE, GA
Parts Used:
WH01X10302, WH41X10096
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Socket set
Replaced the rib belt.
I watch a YouTube video. Showing how to put the new belt on with a zip tie. 100 percent. Success. Thank you for the correct part.replacing the drain was very ease. Use a socket set.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTWN5550D1WW
106 - 120 of 188