GTAP2000M1WW General Electric Washer - Instructions

I just removed the clip and took off the old knob. I than put the new one on and replaced the clip.

Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.

replaced them & working fine now....

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Watched the repair video on PartSelect website , repair was exactly as they showed on video , grab old agitator at base , give a quick pull and it popped right off , lined up tabs to coupler with new agitator and gave a sharp push down and new agitator snapped right on. Total repair time was approx 5 minutes .

Removed clip (keeper), behind knob, releasing it from shaft. Replace with new knob, and clip.