GMAN3000M2WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from PLAINS, MT
- Parts Used:
- WH41X22935
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Small wire had tried spin out of drain pump. Wore pin hole in the rubber drain hose....
Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from W BROOKFIELD, MA
- Parts Used:
- WH13X23974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water Kept Flowing into the tank even when water should have shut off.
The replacement of this tripe water valve was so easy. My tub kept filling with water even though the water should have shut of. First remove the two hoses from the valve. Second you remove the 3 screws from the steel shield behind the plastic upper control pan panel. Take the shield off. Remove the control panel and lay on the washer. Then take the filler hose to the tub off using pliers to remove the hose clamp. Then take the two screws out of the valve. Twist and remove the valve. That is the removal. Reverse all of these to put it back on and test out. This valve fixed my problem. Anyone can do this who has any basic knowledge of tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beata from STUART, FL
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Water dripping into the washer when washer was not in use
I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from LAKE ST LOUIS, MO
- Parts Used:
- WH2X1198
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
hammering on the tub nut wrench rotated the drive axle & pulley
I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WH02X10383, WH2X1198, WH2X1197
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin, leaking water
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Foris from Nome, TX
- Parts Used:
- WH43X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Washer would not agitate.
Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from LIBERTY, KS
- Parts Used:
- WH02X10383, WH2X1197
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Very loud noise during spin cycle
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from PEARL RIVER, LA
- Parts Used:
- WH38X10017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Had to make the 1-11/16” spanner nut tool
Followed the video guidance supplied by this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Utica, NY
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washed my daughter's toys and broke the agitator
Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VITTORIO from PITTSBURGH, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Wasn't Draining
This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from Yelm, WA
- Parts Used:
- WH12X10498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not regulate the amount of water going into the Machine
I shut off the juice to the Washer, I then removed the 4 torx head screws in the panel, so I could gain access to the switch. I then unpluged a small hose going to the switch, then turned the switch by hand about half a turn & it came right out. I then replaced the switch with the new one by turning it half a turn in opposite direction, replaced hose, put the back panel back on, ran the machine to make sure it was working properly.
It is working fine, thanks to Part Select.com , fast service I would reccomend them to my freinds.
It is working fine, thanks to Part Select.com , fast service I would reccomend them to my freinds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from West Columbia, SC
- Parts Used:
- WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water Leaks
I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!