GIWN3000M0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beverly from Casper, WY
- Parts Used:
- WH2X1197, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
it was leaking
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Murphy, TX
- Parts Used:
- WH2X1197
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
The machnica had recently developed a rumble during the spin cycle
The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from SPOTSYLVANIA, VA
- Parts Used:
- WH11X10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
OLD DIAL BROKE OFF
Ordered wrong part initially but received correct one and just put it on without a problem.. The return process was prompt and easy too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mabry from CLINTON, MS
- Parts Used:
- WH43X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Agitator was broken
First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiberiu from CLEVELAND, OH
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sallie from WEAVERVILLE, NC
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All of the fins on the bottom had broken due to clothes getting caught in them.
Removed the softener despenser by pulling it straight up, then did the same with the agitator, except I had to turn it a little then pull straight up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Kiln, MS
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from Bynum, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from Steamboat Springs, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Eldom, MO
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!