GHWP1000M2WW General Electric Washer - Instructions

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Remove control knob and replace it with new part.

One retaining clip to remove and replace part.

Just slipped it on. No problems, No Tools.

Took all apart.. front off,top off, took basket top off..took the basket assembley out by unhooking the four shocks. Took a picture of all wireing and fittings. Then came the most difficult. The main nut that holds the basket to the main shaft. If you do not have one of the wrenches made for that nut good luck. Between all the gunk and rusty parts around it. It would not budge. I used a pipe wrench and a 3# hammer and it wouldnt budge. It is a oppisite drive nut so it comes off in reverse as a regular one. I ordered the wrench on line to use on the new one i orderd. Had to because the nut was getting chewed up. So waiting to order the parts i needed i ground down the nut with my angle grinder.. worked well. Knowing i had to replace the main drive and bearing it wasnt that bad. Got the nut off... pulled the basket out and then the shot seal. Really looked tore up. So because of the seal leaking, the water drips down onto the main drive and thats what ruined it. Cleaned everything up really nice.. went to put the new seal in and noticed it didnt fit as tight as it should.. so i put some silicone around it and installed everything back together. Still thinking of the seal still i went ahead and finished it all and guess what. It leaked.. the seal in my opinion needs to fit over top of the plastic main bucket not just inside of it. After researching the same problem some guys said they filled the bearing seat with silicone and it helped. Others say the plastic tub needs replaced because the bearing seat is wore out.. the tub is like $70.00. The seal is $8.00. So, what to do? Buy another tub and seal and hope the seal fits in tight, or gob alot of silicone on the seal and older tank and see.. the washer new was like $600.00. Been dicontinued now. The main shaft assembley was $160.00... seal$8.00.. the tool for $15.00...misc stuff still comes out to $200.00 . Now to buy a new tub? Is it worth it or not.. we'll see

Turned off the both the hot and cold water. Removed the hoses from the back of the control panel. Removed 3 panel screws to expose the inside of the component parts. Removed the 2 screws holding the valve. Installed the new valve. Then I pulled off the knob for the temperature control. To remove the switch, you need to press the tab that locks in the switch and turn the switch counter clockwise to remove the switch from the panel. Reverse the operation to reinstall the new switch. Pay close attention to the 4 wires that clip to the switch to get them in proper order. Reinstall the control panel and and reattach the hoses.

I followed partselect repair videos to see how to pop off the front panel and also remove the top control panel. Lay the control panel on top of the washer and leave everything connected. With power disconnected I first checked the fill tube and fill sensor by pulling the rubber tube off the bottom of the drum and blowing in the tube - you can hear the sensor click on and off. It requires more pressure if you set the water level switch to a larger load. This behavior told me the tube and sensor were working but this must be an airtight system to be reliable. To test for slow air leaks I blew in the tube to cause the switch to click, then clamped the rubber tube shut with a C-clamp. I left it overnight and no leaks - the switch was still activated in the morning, as I could hear it click when I released the C-clamp. I then suspected the fill valve, so I plugged in the power cord, set the washer for a load and started it. The water started filling and I unplugged the power cord, which should cause the fill valve to shut off immediately. It did not - it kept on filling with water, but in this case eventually shut off after 60-90 seconds. Since it did not shut off immediately when power was removed I knew the fill valve was sticking. I ordered the fill valve from partselect and received it in a couple days. Replacement was easy - shut off water, remove the hoses, and then 3 screws and two electrical connectors to swap out the valve. Then 3 screws to put the control panel back on and snap the front panel back in place. Done. Since replacing the fill valve the washer has been working perfectly.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

Followed instructions from video for shaft and mode shifter assembly and tub bearing, all went as in video except extremely difficult to remove tub nut. Could not get nut to loosen and when it did finally move it was spinning the whole shaft, had to have the shaft held with a pipe wrench from underneath (2nd person). The tub seal was another issue, removal was easy just as in the video but because water had gotten inside the seal it caused the internal metal of the seal to corrode and rust which deformed the old seal and the plastic of the tub where the seal sits. There was no way the new seal would go in and be tight enough to seal so I put a hose clamp around it, heated the plastic with a heat gun just enough to be able to tighten the clamp several times, let it cool and removed the clamp. It held its shape and the new seal went in snug so I proceeded with the reassembly. Test ran the washer and checked for leaks, no leaks. It has been a week now and approximately 10 loads of clothes cleaned, all is good.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.