GCWP1805D1CC General Electric Washer - Instructions

I had no difficulty dismantling the washer until I got to the hub nut. It was frozen to the cone shaped fitting it was resting in. I had to take a drill and a 3/16" drill bit and drill the flange of the hub nut and then take a chisel and break it off piece by piece. Once that was off, I lifted the tub out and tried to pry off the split ring under the tub and it too was corroded and broke when I tried to pull it off. So I would advise you to buy a hub nut and a split ring if you are replacing the tub bearing, just to be safe. I went to an appliance parts store here in town and bought them. When reassembling the tub, I couldn't get a wrench or pliers on the hub nut to get enough torque to tighten it securely. And since I didn't want to spend $43 to buy a spanner wrench for a one time repair, I went to Harbor Freight and bought a $15 dollar adjustable wrench and cut 3 1/2" off the handle so it would lay flat to the tub and used a hammer to tap on the handle to tighten it securely. If you do not find some way to tighten the tub securely, it will come loose in the spin cycle like it did on me twice before I purchased the adjustable wrench and modified it to work. Plus I still have a useable adjustable wrench. Additionally, I took the washer cabinet, the tub and the tub sleeve and power washed it to get years of grime off of it. The washer now operates like new, saving me hundreds of dollars.

Ordered lid switch from parts select via website. Two days later I received the part in the mail. Instead or re-wiring, I cut wire close to existing bad switch. Splice two wires and cap with wire nuts. Zip tie loose wire to tub housing.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

Disassembled washer removed shaft and drive tube assembly reinstalled new unit and replaced split nut during assembly.

Easy to replace, take off the front cover take off hoses unscrew and attach the new pump. Problem wasn't the pump. Now that I have a new pump, not sure what to do next.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

The washer came apart fairly easy until I tried removing tub nut Huge Problem!! After beating the spanner wrench to death I purchased a $50 43mm impact socket to remove the nut. I cleaned up the tub and shaft and started reassembly by replacing bearing 6006rs that I found locally. When I started installing the tub seal I ran into a major issue. Seal would not fit properly, it was to loose in tub. The seal was not large enough for outside diameter. It was a 1/16 of inch or so off. I tried two seals and neither one would work. After talking with a retired repair tech I found that the tub was bad and that the old seal had corroded so bad that it expanded the tub seal housing. I decided not to spend anymore money for this junk of a washer and I applied rtv sealant & reassembled. I'll use it until it breaks down and trash it, very bad design for tub seal, nothing holds it in place, pushed up out of tub. I don't think the rtv sealant well hold for very long. I do appreciate the instructional video for repairs, they are very helpful for showing procedures as to the repair but it's a new machine that's used and everything comes apart so easy. 5 year old washer doesn't come apart that easy. It took 2 weeks to fix it after waiting on parts and doing a unconventional repair to tub seal. So now my wife has started searching for another washer because this one is running on a prayer!

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

You tube is the only way to go!

I followed partselect repair videos to see how to pop off the front panel and also remove the top control panel. Lay the control panel on top of the washer and leave everything connected. With power disconnected I first checked the fill tube and fill sensor by pulling the rubber tube off the bottom of the drum and blowing in the tube - you can hear the sensor click on and off. It requires more pressure if you set the water level switch to a larger load. This behavior told me the tube and sensor were working but this must be an airtight system to be reliable. To test for slow air leaks I blew in the tube to cause the switch to click, then clamped the rubber tube shut with a C-clamp. I left it overnight and no leaks - the switch was still activated in the morning, as I could hear it click when I released the C-clamp. I then suspected the fill valve, so I plugged in the power cord, set the washer for a load and started it. The water started filling and I unplugged the power cord, which should cause the fill valve to shut off immediately. It did not - it kept on filling with water, but in this case eventually shut off after 60-90 seconds. Since it did not shut off immediately when power was removed I knew the fill valve was sticking. I ordered the fill valve from partselect and received it in a couple days. Replacement was easy - shut off water, remove the hoses, and then 3 screws and two electrical connectors to swap out the valve. Then 3 screws to put the control panel back on and snap the front panel back in place. Done. Since replacing the fill valve the washer has been working perfectly.

Turned off the both the hot and cold water. Removed the hoses from the back of the control panel. Removed 3 panel screws to expose the inside of the component parts. Removed the 2 screws holding the valve. Installed the new valve. Then I pulled off the knob for the temperature control. To remove the switch, you need to press the tab that locks in the switch and turn the switch counter clockwise to remove the switch from the panel. Reverse the operation to reinstall the new switch. Pay close attention to the 4 wires that clip to the switch to get them in proper order. Reinstall the control panel and and reattach the hoses.