GCVH6800J5MS General Electric Washer - Instructions

Removed old pump and replaced. Did not want to wait 2-3 weeks for a repair person

Best to watch youtube video and take the time to take washer apart and gain the access needed. I completed repair and dismantled the filter and cleaned it in about an hour, better than the average of 2 hours.

Removed top and front control panel. Shut off water, disconnect water lines at front and dispenser. Remove dispenser. Remove water inlet pipe by pulling out of boot. Install new pipe.Reverse proceedure. Note, these pipes may tend to split on the bottom.

Removed top cover, loosened front door cover, removed & replaced old cracked plastic 'water inlet tube', reinstalled front door unit & top cover. Very tight space to work in when not completely removing front door unit.

I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.

Accessing the door seal was routine. Removing top and front covers was easy. Lower front cover was a challenge because the leaking door caused the screws holding the panel to rust, so extra effort had to be used not to strip the screw heads. Seal removal was easy, replacing the seal was much more difficult. The majority of the repair time was spent attaching the new seal to the drum. It became a tedious task with a large amount of trial and error. Replacing the front spring clamp also takes some time. Eventually I completed the repair and fixed the problem. I will say that if the washer breaks again, it's going to the dump.

Sandblasted spider to thoroughly clean it and increase ductility.We used aluminum foil covered in 5200 on one side to cover holes eaten through spider. Then glued the spider to the drum and filled inside rim of spider with a nice layer of 5200. If the spider was made of stainless steel, the washer would still be running great. Thanks

Let me begin by saying I'm a woman & don't really think of myself as handy but will try a repair. So at first look we thought we'd have to hire a repairman, but after looking at your website & reading the reviews I realized I could fix it myself (or atleast try). I wouldn't recommend doing this repair yourself without watching the YouTube video showing step by step instructions. It was involved - had to take entire front & top off of washer but overall was an somewhat easy fix. The hardest part to me was getting the 2nd band off of the boot seal primarily due to it's location, so when I put band back on I tried to adjust the angle should I have any other problems. Repair took about 1 1/2 hours but wouldn't have taken as long if I didn't have to fight with nut & bolt on the 2nd band.

Remove the bottom panel. Remove the top. Remove the front panel with the door. Romove the two clamps on the boot seal. Remove the old boot seal. Place the new boot seal on the casing around the drum and ensure you put the gasket nozzle and gasket nozzle washer in place. Install the inside gasket clamp with the clamp bolt to the right as you look at it (Note: ensure the nut is over the tab on the boot gasket and stays lined up there as you tighten it. Replace the front panel of the washer and when it is in place put the boot seal on the outside lip (Note: this is the most difficult part as the gaskets does not like to stay in place as you put the outside clamp on. Replace the washer top. Replace the lower panel (Note: while you have the bottom panel off, you may want to clean the debrie trap which is a white pipe and tray that catches stuff that is left in pockets.) For the entire project I used 7mm and 8 mm sockets, flathead screw driver, and a philips head screw drive.

Unplug the machine. Remove the 4 screws on the back panel of the washer. Loosen the tub pulley bolt. Remove the old belt (mine did not completely break, it was shredded and slipped off the pulley). Replace with the new belt. Tighten the pulley bolt. Put the back panel on. Plug in the washer. It is working like new. :)

First I removed the excess water by using my shop-vac both inside the machine as well as near the bottom drain valve. After cleaning out that valve (which somehow had accumulated a pair of underwear) it was apparent that the drainage pump motor was no working (loud hum, not spinning). Replacement was easy, folowing instructions found everywhere on-line. Now the machine is working perfectly again.

The cycles were taking forever, then would not finish, water running in even when it was supposed to drain. Unplugged washer and water would still run, I had to turn off the water valve. I just removed the top with phillips screwdriver, removed the old valve by uncoupling the water hose, the two electric connectors and the two one screw holding it in place. It fixed the problem completely, washer working 100% now.

hold drive pulley from turning and used socket wrench to remove nut. then pulled off pulley from shaft and belt came off same time. very carefully filed the flat sides of the shaft end where the pulley slides onto. careful not to overfile or round out the she shaft end. carefully tap in place the pulley onto the shaft. install a new nut and tighten it approx. 40 ft pounds or 1/4 turn past tight. do not reuse old nut. pulley comes with a new one and the nylon on the old one is no good once used. once pulley is tight install the belt first onto the motor shaft then work the other end of the belt onto the pulley from top end then turn the pulley wheel counter clockwise as you push more belt onto the pulley wheel. kind of like putting on your bicycle tire on your rim.

I followed the instruction on your site. I disconnected the power to the washer turned off the water turned on the nearest faucets to drain the lines. I removed the water hoses from the machine then took the three screws out of the back at the top of machine that held the lid on then removed the three screws on the top of the lid that hold the plastic piece to the front panel and pushed the lid toward the back and it lifted off. I then took the metal ring clamp off the water line attached to the water inlet valve and took the screw out that is on the back of the machine holding it on removed the wire plugs one at a time and put them one at a time on the new inlet valve so I would not get them mixed up. I then put the valve in place reconnected the water hose and metal clamp put the screw in the back to reattach valve the machine put the lid back on in reverse to removal reattached water hoses to the inlet valve turned the water back on plug in the power and immediately used the machine which works like new 20 minute job from beginning to end. By the way ladies if I can do it you can do it. TC

Followed your instruction, very easy. I installed Camco 90" & 45" Brass elbows to relieve strain on hoses.