GCAP1000M2WW General Electric Washer - Instructions

reconnected the wires and turned the water source on

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

Removed the front of the washer using a putty knife. Removed the old belt and used a shop-vac to c,San up the insides. Placed the belt on the pulley and used three med sized zip ties about one inch apart. I cut off the exposed tail of the zip ties. Got the belt started around and put the belt onto the small pulley. Keeping an eye on the small pulley to make sure the belt did not slip off, I had to push it up a time or two. Then as I pulled the big pulley around, one zip tie broke, replaced it and continued pulling the big pulley, it got tough but with one knee pushing on the drum and pulling with one had it went on. I did slowly turn it to align the belt on the big and small pulleys. Not hard, I recommend a bright flashlight and gloves. I saved a good buck doing it myself :-)

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

replace lid switch

Open up the back of the top front panel by removing two screws. Unhook the wires from the old valve, then slip the small clamp down far enough to pull the old valve stem out of the little tubing. Removed the old valve, then replaced with the new valve.

I followed the Youtube instructions on replacing the valve. So easy.
Getting the wire clamp pushed back from the hose was the only part that wasn't easy but I got it done by being gentle and persistent moving and twisting the wire a little at a time.
Im a 67 yr old woman and was determined not to call in a appliance repair person after I saw how simple the installation could be. Parts Direct is awesome. Will use again in the future for repairs. I feel like I have super powers after doing this myself.

I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.