WMCD2050H6WC General Electric Washer - Instructions

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

follow youtube vid. simple

If you follow the video that part select provides you will be just fine.

Without any research, I imagined it might be the old hoses, so I bought new ones. When attaching them, I saw the threads were stripped at the washer end of the hot water hose. I bought the valve, and unscrewed the nuts holding the console in place. The clamp on the exit hose from the valve was a bit tricky, it was hard to hold it squeezed open while simultaneously maneuvering the hose off the valve. When I received the valve it looked like the electrical connections might be very complicated, but in fact it was very simple, a single plug.

Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

First I removed the Front panel with a screwdriver, poped right out. Disconnected the two wires, removed two clamps from hoses on pump, then two screws at base. removed old pump, installed new pump ,tighten two screws, reinstalled hoses and clamps to pump, then put front panel back on, job completed in less than 1/2 hour. tested washer, pump worked and drained tub. easy fix saved cost to repairman $150 plus part cost.
Thanks for the information , learned how to change pump from another repair story on your web site!!

The pump arrived and because I'd read some of the other stories here I wasn't too upset that it looked different.

I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.

The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.

So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!

Remove front panel by pulling on both sides of it at top.

Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.

Replace hose and re install clamps.

followed instructions on you-tube. shut off water faucets. disconnect hoses from washer. remove three hex screws from back of control panel. lean panel forward and slide to the right, then remove it and lay it down.
remove the two screws that hold the valve to the machine. use pliers to slide the clamp back and remove the hose. repeats these steps in reverse to finish job.
the first valve that partselect shipped leaked from the hot water hookup and was deemed to be defective. partselect credited my account before the part was at their warehouse. great service all around.