WLSR2200J3WW General Electric Washer - Instructions

This was so easy. I used needle nose pliers to reach in and remove the metal clip which had slipped off of the inside of the knob and was on the post the knob was supposed to attach to. Next, I lined up the flat side of the "D" of the inside of the knob to the flat side of the "D" on the post and pushed it in until it snapped into place, and I was done. The dryer now works like new.

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.

I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling onto the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.

I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working

The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.