All Installation Instructions for General Electric Washer WCRE6270H2CC

Customer:: joel from mt vernon, IL
Parts Used:: WH01X39337
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set, Wrench (Adjustable)

two tub dampening straps snapped

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Ignacio from Portage, IN
Parts Used:: WH23X10030
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Washer would not pump water out into drain

First I removed the Front panel with a screwdriver, poped right out. Disconnected the two wires, removed two clamps from hoses on pump, then two screws at base. removed old pump, installed new pump ,tighten two screws, reinstalled hoses and clamps to pump, then put front panel back on, job completed in less than 1/2 hour. tested washer, pump worked and drained tub. easy fix saved cost to repairman $150 plus part cost.
Thanks for the information , learned how to change pump from another repair story on your web site!!

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Mark from Woodruff, UT
Parts Used:: WH23X10030
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set, Wrench set

Pump was noisy, then failed and hummed.

The pump arrived and because I'd read some of the other stories here I wasn't too upset that it looked different.

I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.

The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Mabry from CLINTON, MS
Parts Used:: WH43X10034
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins

Agitator was broken

First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Belinda from FLORENCE, KY
Parts Used:: WH41X10096
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

cracked drain pipe

Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Amy from ROCHESTER, NY
Parts Used:: WH01X10302
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Had to replace drive belt on washer

I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: stanley from Pownal, VT
Parts Used:: WH43X10034
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins

Replaceed agitator

Old agitator was stuck on and i could not pull it of.I used two claw hammers and put the claw under the agitator and broke it free.Worked perfect" Took five minutes "

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Annamarie from FORT LORAMIE, OH
Parts Used:: WH43X10032
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Socket set

Agitator did not agitate

Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the problem.Tom

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sallie from WEAVERVILLE, NC
Parts Used:: WH43X10034
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins

All of the fins on the bottom had broken due to clothes getting caught in them.

Removed the softener despenser by pulling it straight up, then did the same with the agitator, except I had to turn it a little then pull straight up.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Shirley from Kiln, MS
Parts Used:: WH41X10096
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

the hose that came on the machine was too short for a mobile home hookup

Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: John L. from Mandeville, LA
Parts Used:: WH23X10030
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Water pump failed

Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Oraila from RINCON, GA
Parts Used:: WH43X10034
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins

broken part

We pulled out the old parts and then we got the new parts and we put them in,

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: tiberiu from CLEVELAND, OH
Parts Used:: WH43X10034
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins

AGITATOR BROKE

pulled up on agitator and it came off and replaced it with the new one

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Francis from Rochester, NY
Parts Used:: WH23X10030
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Leaking water on final pump out

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Mansfield, OH
Parts Used:: WH23X10030
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

water pump died

Was easy. Removed pump, ordered yours and replaced

1 person found this instruction helpful.

Was this instruction helpful to you?

WCRE6270H2CC General Electric Washer - Instructions