WCSR4170G5CC General Electric Washer - Instructions

I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling onto the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!

Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.

The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.

replace lid switch

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.

Followed instructions that came with part disconnected and connected same steps as disconnection. Piece of cake

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Removed the front of the washer using a putty knife. Removed the old belt and used a shop-vac to c,San up the insides. Placed the belt on the pulley and used three med sized zip ties about one inch apart. I cut off the exposed tail of the zip ties. Got the belt started around and put the belt onto the small pulley. Keeping an eye on the small pulley to make sure the belt did not slip off, I had to push it up a time or two. Then as I pulled the big pulley around, one zip tie broke, replaced it and continued pulling the big pulley, it got tough but with one knee pushing on the drum and pulling with one had it went on. I did slowly turn it to align the belt on the big and small pulleys. Not hard, I recommend a bright flashlight and gloves. I saved a good buck doing it myself :-)

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company

Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.