WCSR2090G8CC General Electric Washer - Instructions

Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.

Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.