WCSR2090G4WW General Electric Washer - Instructions

Removed front panel, cut two wires to switch ( color coded ) snapped old switch out and installed new switch, connected wires with wire nuts. Removed two screws in lid, removed magnet and installed the new one. A caveman could do it!

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success

pulled off cup on top of agataor. scrwed off nut. pulled off agatator. flipted up side down. took off agatator bell wich is on the bottom of the agator. sliped on bell. put agatator back on and scrwed on nut. dont reamber the size of the nut.sorry. put cap on and your done.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Just used hands to pry open the old agitator from the washer. If one angle does not work try another and go in a clockwise direction. The new agitator had a new coupling at the bottom, so I needed something to push it out from the top, found a long metal rod and easily pushed it down and out. Verified that new coupling was exactly the same as the old one. The old one was good so I just pushed the new agitator down on the old coupling and it worked fine.

We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod