GPRE8350K3WT General Electric Washer - Instructions

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

Took top off and replaced bolt.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.

Verified there was 110 volts at the connection at the triple water valve. Removed two 1/4" socket screws and used pliers to slide hose clamp off valve inlet. reversed procedure, turned water back on, problem solved.