GHDSR209H5WW General Electric Washer - Instructions

Just slipped it on. No problems, No Tools.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

Watched video online when I ordered the parts very helpful

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

Removed the top panel and twisted the old pressure switch off counter clockwise. Then disconnect the electrical plug and the plastic hose attached to it. Do the reverse for putting the new one on. Very easy repair that you only need a screw driver for.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.

Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.

Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.