GCWP1005M0CC General Electric Washer - Instructions

Reached down into the washer bowl. Fingers on each side of the agitator base. Quick jolt up agitator popped out adjustable wrench took the bolt. Off of the agitator coupling removed coupling wire, brushed the gear slots installed a new coupling with both new bolt lined up, agitator slots pump, the new agitator on after lined up with a down force quick jolt, then installed the new fabric softener, part on top of agitator

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

You tube is the only way to go!

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

I followed partselect repair videos to see how to pop off the front panel and also remove the top control panel. Lay the control panel on top of the washer and leave everything connected. With power disconnected I first checked the fill tube and fill sensor by pulling the rubber tube off the bottom of the drum and blowing in the tube - you can hear the sensor click on and off. It requires more pressure if you set the water level switch to a larger load. This behavior told me the tube and sensor were working but this must be an airtight system to be reliable. To test for slow air leaks I blew in the tube to cause the switch to click, then clamped the rubber tube shut with a C-clamp. I left it overnight and no leaks - the switch was still activated in the morning, as I could hear it click when I released the C-clamp. I then suspected the fill valve, so I plugged in the power cord, set the washer for a load and started it. The water started filling and I unplugged the power cord, which should cause the fill valve to shut off immediately. It did not - it kept on filling with water, but in this case eventually shut off after 60-90 seconds. Since it did not shut off immediately when power was removed I knew the fill valve was sticking. I ordered the fill valve from partselect and received it in a couple days. Replacement was easy - shut off water, remove the hoses, and then 3 screws and two electrical connectors to swap out the valve. Then 3 screws to put the control panel back on and snap the front panel back in place. Done. Since replacing the fill valve the washer has been working perfectly.

Turned off the both the hot and cold water. Removed the hoses from the back of the control panel. Removed 3 panel screws to expose the inside of the component parts. Removed the 2 screws holding the valve. Installed the new valve. Then I pulled off the knob for the temperature control. To remove the switch, you need to press the tab that locks in the switch and turn the switch counter clockwise to remove the switch from the panel. Reverse the operation to reinstall the new switch. Pay close attention to the 4 wires that clip to the switch to get them in proper order. Reinstall the control panel and and reattach the hoses.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.