WMSR3110W1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Justin from New Orleans, LA
- Parts Used:
- WH49X10042, WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Agitator not working
I just added the agitator coupling and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not rotate
1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from hastings, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
washer would not agitate
The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- akram from lakewood, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
the washer would work but the agitator wouldnt spin
took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REX from PLEASUREVILLE, KY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
agitator couplier was stripped out on the shaft
I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cincinnati, OH
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob won't engage
Remove retaining clip, remove knob, inspect for wear. Order part, install part (knob), resume operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamara from Wellston, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
the stupid washer would not empty the water
Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from bradford, VT
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burley from WINTER PARK, FL
- Parts Used:
- WH41X10077
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fill nozzle had a leak
Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cumberland, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Silver Spring, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not empyting
Removed front cover, disconnected wires and hoses, reversed process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Edina, MO
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
washing machine quit agitating
took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
Was this instruction helpful to you?
Thank you for voting!