WPRB9220D1CC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catherine from Keizer, OR
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator spun but would not agitate
Replaced the plastic agitator coupler
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ranburne, AL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator coupling in my washer was stripped out.
I had already removed the old coupling by removing pulling the agitator straight up off the coupling, then I removed the bolt that held the coupling in, and pulled the coupling up off the shaft.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from LAKE ST LOUIS, MO
- Parts Used:
- WH2X1198
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
hammering on the tub nut wrench rotated the drive axle & pulley
I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WH02X10383, WH2X1198, WH2X1197
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin, leaking water
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from Berkeley, CA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tammy from tracy, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the agitator was not sping
figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Davie, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Debris in pump
Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VITTORIO from PITTSBURGH, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Wasn't Draining
This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from EAST PEORIA, IL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Very loose agitator so I thought
I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Richland Hills, TX
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washing machine quit pumpig the water out.
Removed the old one and installed the new pump, by removing the front cover and disconnect everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Christiana, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
agitator not spiining under load
1, remove agitator. 2 on top of the agitiataor coupling you will see a bolt. Rap lightly with a hammer and with vice grips gently remove the bolt. why vice grips if its been in there for awhile this will be your best choice. No worries the kit comes with a new one.3 Pull the coupling sraight up and out. 4. Align the splines of the new coupling with shaft and gently tap the new one on. 5 Lube the oring and tighten bolt. 6 align the splines of the agitator and gently seat the agiator all the way down. might take awhile to align everything.
trouble shooting tip remove the front cover, turn machine on and hold the agitator, no, not the kid, the one in the machine. If the agitator stops moving but the machine continues to work and the belt or pump shaft turns its the coupling.
trouble shooting tip remove the front cover, turn machine on and hold the agitator, no, not the kid, the one in the machine. If the agitator stops moving but the machine continues to work and the belt or pump shaft turns its the coupling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from COCOA, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
the water, not get out (drain)
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
Was this instruction helpful to you?
Thank you for voting!