WMSE3140A0AA General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kelvin from Richland Hills, TX
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washing machine quit pumpig the water out.
Removed the old one and installed the new pump, by removing the front cover and disconnect everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Riverbank, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was no longer moving
I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Wytheville, VA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Agitator Not Working
I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamara from Wellston, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
the stupid washer would not empty the water
Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Beaumont, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would finish a cycle and the water would not drain the tub.
I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from New Orleans, LA
- Parts Used:
- WH49X10042, WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Agitator not working
I just added the agitator coupling and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Western Springs, IL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
would not drain water
Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from hastings, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
washer would not agitate
The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not rotate
1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Singers Glen, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump was broken
So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from willard, NC
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water leaking from bottom of washer
removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SHIRLEY, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water would not pump out of the unit or spin
If you follow the video that part select provides you will be just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Eldom, MO
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from baltimore, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Bought the unit used and noticed when i opened the front of the washer indications of the pump leaking and some rust on the pump/motor bracket.
First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy
Was this instruction helpful to you?
Thank you for voting!