WPSP4170W0WW General Electric Washer - Instructions

The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

If you follow the video that part select provides you will be just fine.

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

Was easy. Removed pump, ordered yours and replaced

I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..

Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!

This site and buying experience WOWED ME!!! After realizing what happened, I searched how to open up a washer, since I had never done it before. My search brought me to your site, which had an excellent 'how to' video for my exact problem of replacing the pump! I ordered the part, which was delivered to my door in LESS than 24 hours! Unfortunately, there was undrained water in the washing machine so while undoing the clamps on the old pump, the water drained on my kitchen floor, so beware of that issue. Because of the positioning of the pump, the clamps were a little tricky to redo, but completed without too much difficulty. I also had to 'unplug' (with a coat hanger snake)the drain tube connecting the pump to the back of the washing machine so it could flow to the outside drain pipe. This was the best internet buying experience I have ever had! Thank you so much! I fixed a 15 year old washing machine for about $40.00!!! (And I am a 57 year old grandmother ;-) Woohoo!!!

Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

Replaced pump. New pump same manufacturer and model, but better built; however, base plate not same, requiring that I swap it for the original. Also, pump suction inlet is straight-in, whereas original has 90 degree connection. Disconnect power, and remove old pump. Purchase a 1 1/2" I.D. auto radiator hose, cut off use the 90 degree bend; it's a perfect fit to pump conn.; use a 1" PVC coupling on other end socket to mate to the washer drum convoluted drain hose socket. Throw away the crappy original G.E. hard-to-use spring hose clamps and use stainless steel automotive type gear clamps instead. WARNING: Do not try to bend, stretch, or kink the rubber tub drain hose to fit up to the pump without installing an elbow; the installation geometry must be exactly the same as the factory-designed installation. To finish the job, power up and run the machine through several cycles with the front cover off to check for leaks. You will also see why the rubber drain hose must be reinstalled as described above. This washer does not ramp down speed when in the spin cycle, and when the motor stops, the drum makes a sudden 15 to 30 degree rotation, stretching the drain hose to it's limit. Finally, keep your hands out of the machine when it's running; the motor, belt, and transmission drive can cause some real damage if you get tangled up in them. Pay attention to what you are doing; if you are confused by my little dissertation, hire someone qualified to do the job for you.

Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.

I took of the old clip an broken piece of the knob, and removed the selection plate, and push on the new knob and clip, using my pliers.