WCSR4110TAWW General Electric Washer - Instructions

An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!

Took the top cup off the agitator, popped out the agitator by grabbing it with both hands and yanking, unscrewed the nut to the agitator coupling, put the new one on and tightened it up, popped the agitator back on. Works great no problems. Though I did find out that the factory had changed the part sometime ago and it actually did need to be replaced.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

I did this by myself and it was so easy. I'm a tiny female so it didn't take a lot of muscle and I only got one bruise :) I pulled the agitator off, there was no screw holding it in place. Removed the screw that was holding the coupler on with a socket set. Put the new coupler in place, used the socket set to screw it on, popped the agitator back on and crossed my fingers.....It worked like it was brand new. So happy, apparently the old coupler was stripped out. Super fast shipping and I will come back for other parts as needed. Thanks so much!

Easiest repair ever. My wife actually did the repair because I thought I'd need more time to do it. She just pulled the agitator staight up and out then removed the bolt holding the coupling, pulled out the defective coupling and put the new one in, replaced the bolt, slid the agitator back on and it worked perfectly! Thanks for making a $60 or more repair call a $13 dollar self repair. And that includes shipping! We will always use your site for future fixes.

Found out the screw was stripped from the agitator, probably because the washer is over 10 yrs old. We got the right part! The parts store was very fast in shipping, in fact we got it the next day! Highly recommend PartSelect!!!!!!!!!!

pulled out the center agitator, undid the nut , put the new one on , easiest repair ever, less that 13 dollars. and the part came in 2 days, wow, I am impressed with your company!!!!!