WCRE6270D0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jesus from Casa Grande, AZ
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Water was not draining from washer
My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Wytheville, VA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Agitator Not Working
I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Western Springs, IL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
would not drain water
Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from willard, NC
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water leaking from bottom of washer
removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L. from Mandeville, LA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water pump failed
Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from RED BANK, NJ
- Parts Used:
- WH43X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser was missing cup to hold softener.
Took old one out and put new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from MANHATTAN, KS
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Start knob broke off
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MONROEVILLE, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob
Just push knob on less than 4 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathaniel from Rutherfordton, NC
- Parts Used:
- WH49X10042, WH43X139
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
washer not agitating
After discovering the agitator floating in the basket and being torn apart from the spin cycle, I finally narrowed the problem down to the coupling having stripped. Removing the old coupling from the agitator itself took a pretty hefty yank and a large pliers, but after that this went pretty easily.
The bolt that holds the coupling onto the spline, as it turns out, is too short. The new part corrects this design flaw and prevents the bolt from working its way out over time. I took the liberty of applying some loctite to the threads before sliding the new coupling on--this needed a wood block and hammer to fully seat-several years worth of grime on the spindle makes for a snug fit-then installed the new bolt. Agitator snaps on top, then the cap that had been shredded when it floated around snapped in.
Hardest part was getting the failed coupling out of the agitator--design of the unit is not easy to find and thus determine which parts to pull on. Other than that, 15 minutes and this one is done.
The bolt that holds the coupling onto the spline, as it turns out, is too short. The new part corrects this design flaw and prevents the bolt from working its way out over time. I took the liberty of applying some loctite to the threads before sliding the new coupling on--this needed a wood block and hammer to fully seat-several years worth of grime on the spindle makes for a snug fit-then installed the new bolt. Agitator snaps on top, then the cap that had been shredded when it floated around snapped in.
Hardest part was getting the failed coupling out of the agitator--design of the unit is not easy to find and thus determine which parts to pull on. Other than that, 15 minutes and this one is done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Edina, MO
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
washing machine quit agitating
took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Silver Spring, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not empyting
Removed front cover, disconnected wires and hoses, reversed process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!