YISR309JTAAA General Electric Washer - Instructions

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

Reaching into the washer I placed both hands on the bottom of the agitater 180 degrees apart and lifted the agitater straight up out of the tub. Using a 7/16 socket I removed the coupling kit. The new one slid right on. I secured it with the new bolt supplied with the kit. The agitater went right back on the new coupler and I was done. Fast, simple and inexpensive. Thanks so much to Part Select.

Repair was so simple. I used both hands to pull of the inside assembly of the washing machine. Loosened bolt with a pair of pliers. Replaced worn out agitator with new one along with new bolt. I tightened the bolt and pur back on the inside assembly and was done in less than five minutes. The part came to my house in only three days and the instructions were easy to read and understand!

Took the top cup off the agitator, popped out the agitator by grabbing it with both hands and yanking, unscrewed the nut to the agitator coupling, put the new one on and tightened it up, popped the agitator back on. Works great no problems. Though I did find out that the factory had changed the part sometime ago and it actually did need to be replaced.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

I did this by myself and it was so easy. I'm a tiny female so it didn't take a lot of muscle and I only got one bruise :) I pulled the agitator off, there was no screw holding it in place. Removed the screw that was holding the coupler on with a socket set. Put the new coupler in place, used the socket set to screw it on, popped the agitator back on and crossed my fingers.....It worked like it was brand new. So happy, apparently the old coupler was stripped out. Super fast shipping and I will come back for other parts as needed. Thanks so much!

Easiest repair ever. My wife actually did the repair because I thought I'd need more time to do it. She just pulled the agitator staight up and out then removed the bolt holding the coupling, pulled out the defective coupling and put the new one in, replaced the bolt, slid the agitator back on and it worked perfectly! Thanks for making a $60 or more repair call a $13 dollar self repair. And that includes shipping! We will always use your site for future fixes.

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

pulled out the center agitator, undid the nut , put the new one on , easiest repair ever, less that 13 dollars. and the part came in 2 days, wow, I am impressed with your company!!!!!

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

Found out the screw was stripped from the agitator, probably because the washer is over 10 yrs old. We got the right part! The parts store was very fast in shipping, in fact we got it the next day! Highly recommend PartSelect!!!!!!!!!!