WLRE4500G0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dale from Wrightwood, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
wouldn't pump water
I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Wiscasset, ME
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Washer would not pump water out of basin
I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Meriden, CT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Washer wouldnt drain
First I removed the front cover, Drained out water by hand, Romoved two drain hoses going into old pump,removed the electric very easy it was two wires,installed new pump and reconected all. Now my wife is happy again and so am i. Your installation video was the KEY to my success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Kiln, MS
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L. from Mandeville, LA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water pump failed
Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oraila from RINCON, GA
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken part
We pulled out the old parts and then we got the new parts and we put them in,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Rochester, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water on final pump out
Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mansfield, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water pump died
Was easy. Removed pump, ordered yours and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SHIRLEY, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water would not pump out of the unit or spin
If you follow the video that part select provides you will be just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mabry from CLINTON, MS
- Parts Used:
- WH43X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Agitator was broken
First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from baltimore, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Bought the unit used and noticed when i opened the front of the washer indications of the pump leaking and some rust on the pump/motor bracket.
First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiberiu from CLEVELAND, OH
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!