WWSR3090TAWW General Electric Washer - Instructions

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you

Reaching into the washer I placed both hands on the bottom of the agitater 180 degrees apart and lifted the agitater straight up out of the tub. Using a 7/16 socket I removed the coupling kit. The new one slid right on. I secured it with the new bolt supplied with the kit. The agitater went right back on the new coupler and I was done. Fast, simple and inexpensive. Thanks so much to Part Select.

Resigning myself to the fact that the washer was broken and I would need to buy a new one, I decided to pull it apart to see if I could see what the problem was (why not if your getting a new one anyway) Once I muscled the agitator off and undid the screw I discovered that the agitator coupler sat on a metal piece that had grooves. Alas...the coupler was worn...there were no grooves left inside the plastic piece. Wondering if I could even find this part I wondered onto this website, plugged in the part number and there it was with pictures and measurements and cheap! Needless to say I ordered it, why not, if it doesn't work I will buy a washer anyway. The part arrived within days. I unpacked the box, opened the plastic, slid it into place, tightened the new screw, replaced the agitator, plugged it back in, started it up and the washing machine was agitating like new. I wrote this long story because the repair was so easy it's not even funny, and I was just going to buy a new washer...

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

This was an inexpensive part with high probability of needing it, so I ordered it before beginning to take the washer machine apart based on "noisy" symptom. The fabric softener cup pulled straight up easily with no tool. Then, the agitator pulled straight up easily with no tool. The bolt was easy to get to with socket set and the coupler pulled up using 2 small pieces of wood as levers to pull it up evenly and straight. This didn't solve my noise problem, but was an easy and inexpensive fix to try. FYI...when I continued trying to troubleshoot, I took the belt off and the noise stopped, so I think the transmission is my problem. I tried for 2 days with WD-40, then with C-L-R to get the hub nut to move, and couldn't. I then tried to split the nut using a screwdriver and a hammer and it appears to be split in 2 places, but the nut still won't budge. I listed the washer on craigslist today too frustrated with the hub nut to continue the repair job. The cost of a repairman plus the transmission would have been over half of a new washer machine, and I still would have had a 8+ year-old motor, and I ran across a great deal on a scratch and dent model at Sears, so I am replacing the washer instead of repairing it.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

I did this by myself and it was so easy. I'm a tiny female so it didn't take a lot of muscle and I only got one bruise :) I pulled the agitator off, there was no screw holding it in place. Removed the screw that was holding the coupler on with a socket set. Put the new coupler in place, used the socket set to screw it on, popped the agitator back on and crossed my fingers.....It worked like it was brand new. So happy, apparently the old coupler was stripped out. Super fast shipping and I will come back for other parts as needed. Thanks so much!

Easiest repair ever. My wife actually did the repair because I thought I'd need more time to do it. She just pulled the agitator staight up and out then removed the bolt holding the coupling, pulled out the defective coupling and put the new one in, replaced the bolt, slid the agitator back on and it worked perfectly! Thanks for making a $60 or more repair call a $13 dollar self repair. And that includes shipping! We will always use your site for future fixes.

Simple replacement. Very easy.