WWSR3090TAWW General Electric Washer - Instructions

Easy as it gets. I did this repair while playing Wii with my 8 year old and cooking supper... Still no more than a 10 minute fix.

Place a towel on one side of the washer so you won't scratch it.

Tie a loop of rope around the middle of the agitator between the upper and lower fins. Wrap the other end of the rope around a 2x4 ( I used a level), or anything similar and wind it around until the 2x4 is pulled down level with the top, keeping one end on the towel.

Yank the other end firmly a few times, and the agitator will seperate from the coupling. I had to snatch it pretty hard.

I removed the 7/16" bolt from the coupling, pulled it off the spline and replaced it with the new one.

The agitator slid right back into place with no trouble, and it is good as new.

What seemed like an expensive repair, or even the need for a new appliance was essentially removing one bolt and a replacing a $6 part.

Thanks!

Agitator came off easily, but the agitator coupling was a little bit hard to remove. I have to yank it hard to be able to remove it. Putting the new part in is a bit hard too. I had to use a hammer to put it in. (with a piece of wood in between). Tried it with a small load and We're back in business. It was a pleasant experience to do business with you guys. Thanks for the quick turnaround.

I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.

Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

plug new knob.

I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone

This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.

Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........

Unplugged washing machine pulled Agitator strait up removed screw from center of Agitator coupling . Replaced coupling put Agitator back on plugged in and done.

First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).

It was really simple just pull up the agitator and take off the screw that holds the coupling down slide it off and put the new coupling on and you are done.

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

Took the top cup off the agitator, popped out the agitator by grabbing it with both hands and yanking, unscrewed the nut to the agitator coupling, put the new one on and tightened it up, popped the agitator back on. Works great no problems. Though I did find out that the factory had changed the part sometime ago and it actually did need to be replaced.