WPSL3120W0WW General Electric Washer - Instructions

I took a pair of pliers removed the clip and pushed the new one on. Easy fix .

first i removed the spindle and theni removed theplastic coupling

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len

First, I removed the agitator by reaching in the washing machine and pulling up on the agitator until it popped off. Next, I removed the 1/4" bolt that attached the coupling to the spline. Then I removed the coupling. After removing it, I replaced it with a new one, installed a new bolt, and reattached the agitator. It took 2 days for me to get the part(ordered on a Sun)but only took me 10 minutes to repair.

First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).

I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.

easy to repair. instructions (with pictures) were included with the part. part came super fast.

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.

I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone

I just pushed the new knob on the shaft and was done

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you