WPSL3120W0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Littleton, CO
- Parts Used:
- WH38X10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Transmission bearing went out creating alot of noise on every cycle.
I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from House Springs, MO
- Parts Used:
- WH38X10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Tranny oil ran out onto Laundry room floor/making noise
Removed front cover(use screwdriver)clips on top of cover under lid
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Porter, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator not agitating
Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ephrata, PA
- Parts Used:
- WH11X10033, WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
teeth were stripped on dial
Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from NORWALK, CT
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Old Knob Broke.
I replaced the old knob with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lapeer, MI
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Lewiston, ID
- Parts Used:
- WH11X10033, WH01X10310
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The edge of the knob wore out
I pulled the old knob off and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Eddyville, KY
- Parts Used:
- WH38X10002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
transmission not working
Should be noted that the basket must be rotated on installation to find the best balance point!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dylan from Davie, FL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
I took off the broken knob since it was already loose. Then I removed the new part from its wrapper and lined the bolt up the knob. Inserting and pushing until it felt like the knob had a firm grip the job was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from New York, NY
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob on my Mom's washing machine
Folks,
Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!
Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Butch from WATER VALLEY, MS
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Machine would not agitate.
Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Canastota, NY
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The knob on my washer would not turn so I could select load size
I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michele from Deerfield Beach, FL
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer needed new knob and clip
simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Due West, SC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
My Washer stopped agitating
Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Betterton, MD
- Parts Used:
- WH45X10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The machine would not spin and the agitator seemed to be siezed up. The inner tub had cracked and broken completely loose causing it to jam against itself preventing any movement.
1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.
Was this instruction helpful to you?
Thank you for voting!