WCSR2090G1WW General Electric Washer - Instructions

First removed the screws on the contraol panel. Then I pulled the tubing from the part. Snapped teh switch preesure out. Put the new one in. Attached the tubing. Put control panel back together.

Folks,

Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!

This sounds like an easy fix to replace the shaft seal after watching the video, Oh how WRONG was I.....Firstly the video and parts list show just pull the agitator off..... NOOOOOO the bolt (Screw) is deep inside the agitator and that has to be removed to get the agitator off.....maybe in some models they have changed this poor design but not mine....As the screw is open to all the water and detergent guess what, it was so corroded you could get a sock to grip on it. Only solution was to cut the agitator in half at the bolt head level to get a vice grip on the rounded bolt head to undo it........It doesn't stop there, then you have to remove the fins in the remaining part agitator to get get the vice grips on. OK so far so good, now try and undo the big left hand thread nut....good luck, totally corroded, tried penetrating oil, heating it up you name it, nothing. I had a 1 11/16 socket but you need a deep socked as the shaft protrudes too far...solution drill the nut in three places to break it off the thread....OK so far we are winning....Now try to get the split spacer off the corroded shaft, no way was that going to happen it did eventually span in half so had to buy that too.....NOW WE STILL have to get the washer off the shaft...Run out of space to continue...

The "service kit belt tool" was difficult to install, but I oonsider it a necessity. We tried installing the belt without the tool, and the belt kept snapping off the motor drive pulley. Using a cable tie to hold the belt to the drum pulley did not work. I used a length of heavy duty duct tape instead, and that worked OK. Unfortunately, the whining noise is still present with the new belt, so a GE service technician visit has been scheduled. Our belt replacement effort has not been totally wasted, unless the washer can't be repaired economically, since the old belt was fraying.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Remove control knob and replace it with new part.

One retaining clip to remove and replace part.

Just slipped it on. No problems, No Tools.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

You tube is the only way to go!

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.