WJSR2070B0CC General Electric Washer - Instructions

This site and buying experience WOWED ME!!! After realizing what happened, I searched how to open up a washer, since I had never done it before. My search brought me to your site, which had an excellent 'how to' video for my exact problem of replacing the pump! I ordered the part, which was delivered to my door in LESS than 24 hours! Unfortunately, there was undrained water in the washing machine so while undoing the clamps on the old pump, the water drained on my kitchen floor, so beware of that issue. Because of the positioning of the pump, the clamps were a little tricky to redo, but completed without too much difficulty. I also had to 'unplug' (with a coat hanger snake)the drain tube connecting the pump to the back of the washing machine so it could flow to the outside drain pipe. This was the best internet buying experience I have ever had! Thank you so much! I fixed a 15 year old washing machine for about $40.00!!! (And I am a 57 year old grandmother ;-) Woohoo!!!

took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .

ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.

I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.

The pump arrived and because I'd read some of the other stories here I wasn't too upset that it looked different.

I used pliers to squeeze the hose clamps and remove them from the old pump. The hex screws holding the old pump in were sort of rusty due to water, and were the majority of the miminal problem I had getting the old pump out. I put the new one in easily, fussed with the hoses a bit to make sure the clamps were in the right spot, plugged in the two leads, and ran a load.

The new pump was so quiet that I wasn't sure it was even working. Of course it was, and for $50 I gave myself a washing machine that works again. Thanks, guys.

First I removed the front cover, Drained out water by hand, Romoved two drain hoses going into old pump,removed the electric very easy it was two wires,installed new pump and reconected all. Now my wife is happy again and so am i. Your installation video was the KEY to my success.

watched Partselect video and followed instructions step by step

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.

I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..

follow youtube vid. simple

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

If you follow the video that part select provides you will be just fine.

Was easy. Removed pump, ordered yours and replaced

The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.

Removed the old pump put in the new one

Replaced pump. New pump same manufacturer and model, but better built; however, base plate not same, requiring that I swap it for the original. Also, pump suction inlet is straight-in, whereas original has 90 degree connection. Disconnect power, and remove old pump. Purchase a 1 1/2" I.D. auto radiator hose, cut off use the 90 degree bend; it's a perfect fit to pump conn.; use a 1" PVC coupling on other end socket to mate to the washer drum convoluted drain hose socket. Throw away the crappy original G.E. hard-to-use spring hose clamps and use stainless steel automotive type gear clamps instead. WARNING: Do not try to bend, stretch, or kink the rubber tub drain hose to fit up to the pump without installing an elbow; the installation geometry must be exactly the same as the factory-designed installation. To finish the job, power up and run the machine through several cycles with the front cover off to check for leaks. You will also see why the rubber drain hose must be reinstalled as described above. This washer does not ramp down speed when in the spin cycle, and when the motor stops, the drum makes a sudden 15 to 30 degree rotation, stretching the drain hose to it's limit. Finally, keep your hands out of the machine when it's running; the motor, belt, and transmission drive can cause some real damage if you get tangled up in them. Pay attention to what you are doing; if you are confused by my little dissertation, hire someone qualified to do the job for you.