WNRD2050DCWC General Electric Washer - Instructions

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!

Removed front cover, disconnected wires and hoses, reversed process

removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

First I removed the Front panel with a screwdriver, poped right out. Disconnected the two wires, removed two clamps from hoses on pump, then two screws at base. removed old pump, installed new pump ,tighten two screws, reinstalled hoses and clamps to pump, then put front panel back on, job completed in less than 1/2 hour. tested washer, pump worked and drained tub. easy fix saved cost to repairman $150 plus part cost.
Thanks for the information , learned how to change pump from another repair story on your web site!!

After doing some research on the problem I decided that the rubber tub dampers were probably the problem. Replacing them was simple and straight forward after watching the video. A test spin after installation revealed that the problem still existed. This time I watched the bottom of the tub with a flashlight as the spin cycle began and I discovered that the concrete counter-weight was loose on its platform. General Electric had attached a 5 lb concrete block to the tub support with two self tapping sheet metal screws that had stripped out. I screwed the screws back in and added two nuts to the protruding screw bottom and locked them together. Problem solved. The main difficulty in this repair is reaching to the back of the washing while laying on the floor. And sharp edges on everything.