WCRD2050F1WC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Campbell, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Two out of Four Straps were Torn
First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Syracuse, IN
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Would not agitate
Reading all the other stories helped me get started. One tip I want to share is when removing the old coupler, I held on to a pulley puller by hand. I hooked the jaws underneath; while I pulled up on it, I would tap with a hammer on either side of the old coupler. This gave me the leverage needed to make it pop right off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from West Columbia, SC
- Parts Used:
- WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water Leaks
I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from COCOA, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
the water, not get out (drain)
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from EAST PEORIA, IL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Very loose agitator so I thought
I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST CHESTER, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Stopped agitating
I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from BRADFORD, RI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not pump out
Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesus from Casa Grande, AZ
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Water was not draining from washer
My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Brookville, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Clothes washer agitator stopped moving. Threads inside coupling were worn so badly the agitator was free moving.
***Partselect.com had my ordered part delivered within 3 days.*** First, I pulled up on agitator and removed it. Then, loosened bolt on coupling and removed it. Replaced with new coupling, placed and tightened new longer bolt that came with new coupling. Replaced agitator and started laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Spotsylvania, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
would not drain
watched Partselect video and followed instructions step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SHIRLEY, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water would not pump out of the unit or spin
If you follow the video that part select provides you will be just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mansfield, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water pump died
Was easy. Removed pump, ordered yours and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L. from Mandeville, LA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water pump failed
Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.
Was this instruction helpful to you?
Thank you for voting!