WICB103CV1WC General Electric Washer - Instructions

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........

This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!

Resigning myself to the fact that the washer was broken and I would need to buy a new one, I decided to pull it apart to see if I could see what the problem was (why not if your getting a new one anyway) Once I muscled the agitator off and undid the screw I discovered that the agitator coupler sat on a metal piece that had grooves. Alas...the coupler was worn...there were no grooves left inside the plastic piece. Wondering if I could even find this part I wondered onto this website, plugged in the part number and there it was with pictures and measurements and cheap! Needless to say I ordered it, why not, if it doesn't work I will buy a washer anyway. The part arrived within days. I unpacked the box, opened the plastic, slid it into place, tightened the new screw, replaced the agitator, plugged it back in, started it up and the washing machine was agitating like new. I wrote this long story because the repair was so easy it's not even funny, and I was just going to buy a new washer...

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

This was an inexpensive part with high probability of needing it, so I ordered it before beginning to take the washer machine apart based on "noisy" symptom. The fabric softener cup pulled straight up easily with no tool. Then, the agitator pulled straight up easily with no tool. The bolt was easy to get to with socket set and the coupler pulled up using 2 small pieces of wood as levers to pull it up evenly and straight. This didn't solve my noise problem, but was an easy and inexpensive fix to try. FYI...when I continued trying to troubleshoot, I took the belt off and the noise stopped, so I think the transmission is my problem. I tried for 2 days with WD-40, then with C-L-R to get the hub nut to move, and couldn't. I then tried to split the nut using a screwdriver and a hammer and it appears to be split in 2 places, but the nut still won't budge. I listed the washer on craigslist today too frustrated with the hub nut to continue the repair job. The cost of a repairman plus the transmission would have been over half of a new washer machine, and I still would have had a 8+ year-old motor, and I ran across a great deal on a scratch and dent model at Sears, so I am replacing the washer instead of repairing it.

First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

Unplug power. Pull up firmly and quickly from the base of the agitator. Some videos used a rope and 2x4, I didn't have to. The agitator just pops right off. Then with a 7/16" wrench unscrew the bolt while holding on to the coupling. Take agitator coupling off. Clean off metal grooves that the coupling goes on, use either a small screwdriver, metal brush, a knowl, just to make sure you will have good connection with the new coupling. Then install the coupling, new nut, tighten nut firmly. Install agitator pushing down firmly on opposite sides until snaps in place. Turn agitator by hand, it should not free spin. Plug power back in, run washer with water and bleach only in the smallest setting and let it run through its cycle. This will take care of any black debris that might have got into the bowl while fixing. GOOD LUCK!! I also used videos found on Google.